Pinhole Filler Paste for Surface Repair

Concrete Repair

Pinhole Filler 900ml - 2 Part Resin Repair Paste for Concrete & Coatings

900ml two-part resin pinhole filler (880ml resin + 20ml activator) for small cracks, blemishes and pinholes, sandable in 15-20 minutes.

SKU RCD326

£126.58 incl. VAT

Key features

  • High resin content
  • Lightweight and smooth
  • Easy to mix, use and apply
  • Good adhesive strength
  • Specially formulated for easy sanding
  • DIY friendly
Size: 900ml (880ml Resin + 20ml Activator)

Product details

Product description

An ultra-strong, lightweight, multi-functional repair filler for small cracks, blemishes and pinholes in concrete, screeds, self-levelling layers, metals and resin coatings. Easy to use, it cures quickly to high strength while staying easy to sand and abrade for further coating.

This off-white paste fills pinholes and repairs surfaces with grind marks, low spots and other minor imperfections, and is particularly suited to filling pinholes in coatings and substrates. Its high resin content gives a less porous finish that reduces paint absorption and improves durability, while its low viscosity lets it flow easily into small pinholes for a seamless repair. It offers excellent adhesion and blends well with the surrounding area.

Preparation

The substrate must be fully cured before you start. Vacuum the area thoroughly to remove any loose material or debris that could make the filler set unevenly. Clean and degrease so the area is free from oil, grease and dirt, then abrade with medium grit paper – glossy surfaces especially benefit from gentle sanding to key them. Finish with a final clean to remove all sanding dust.

Mixing & Application

The filler will not cure without the supplied hardener, which gives approximately 5-6 minutes of working time, so do not mix more than you can use in that time. Using slightly less hardener slows the process down, but this is done at your own risk.

  1. Dispense a 10cm puddle of Part A onto a suitable mixing surface – clean scrap plastic or a ceramic tile is ideal.
  2. Lay a single 10cm ribbon of Part B across the puddle.
  3. Mix thoroughly with the included spreader in a figure-of-8 motion until the colour is completely uniform, following the mix ratio carefully so as not to under- or over-catalyse.
  4. Apply to the repair in thin layers with firm, pressing pressure to reduce trapped air – the soft paste enters pinholes easily.
  5. Allow to cure for 15-20 minutes, then sand to a smooth finish with medium to fine sandpaper (200 grit or finer). Sanding later is possible but takes more effort.

Pot life is 4 minutes – once mixed, the material starts to cure chemically after this time, so remove it from the tin within this window. It then stays workable on the floor for up to 6 minutes.

Useful Information
  • Fill all pinholes before priming. Once primer is applied, further minor pinholes in the substrate may show up – a second round of filling at this point gives the best finish.
  • The filler must be over-coated with an epoxy, polyurethane or polyaspartic coating.
Please Note
  • Do not apply on new or wet concrete (under 21 days old, or with a residual moisture content of 6% or higher).
  • Do not apply below 7°C or expose to freezing conditions; temperatures below 20°C slow curing and drying times.
  • Do not expose to chemicals, wash, or allow water to rest on the surface until 7 days after application.
  • Not UV stable – do not expose to prolonged sunlight, as it will discolour.

Specifications

Size
900ml (880ml resin + 20ml activator)
Appearance
Off-white paste
Composition
880ml resin and 20ml activator
Substrates
Concrete, screeds, self-levelling layers, metals and resin coatings
Product Components
Resin (Part A) + Activator (Part B), plastic spreader supplied
Typical Installations
Repairing small cracks, blemishes and pinholes
Drying Time (at 20°C)
15-20 minutes
Pot Life
4 minutes
Working Life
6 minutes
Shelf Life
12 months
Minimum Temperature
7°C
Maximum Depth (applied as a layer)
3mm
Maximum Depth (filling pinholes under 1mm diameter): Unlimited
Application Tools
Plastic spreader (supplied)

Quote request

Get a quote for this product

Pinhole Filler 900ml - 2 Part Resin Repair Paste for Concrete & Coatings

We only use your details to reply to this request. See our privacy policy.

Frequently asked questions

What is the return policy?

You can return unused, unopened items in their original sealed packaging within 14 days of delivery, with no restocking fee. Contact us first to arrange the return. You pay return postage if you've changed your mind, and we pay if the item is faulty, damaged or incorrect. Refunds go to your original payment method within 5 working days of us receiving your return. Products made, mixed or tinted to your specification can't be returned unless they're faulty. Full Return & Refund Policy

When will I get my order?

Orders are dispatched within 1–2 working days. Delivery then takes 2–4 working days after dispatch, so the total estimated delivery time is 3–6 working days from order.

Orders placed before 2pm (UK time) on a working day are processed the same day. Orders placed after 2pm, at weekends or on UK bank holidays are processed from the next working day. Working days are Monday to Friday, excluding UK bank holidays.

 Full Shipping Policy

Which payment methods do you accept?

We accept Visa, Mastercard, Maestro, American Express, Diners Club, Discover and UnionPay. You can also pay with Apple Pay, Google Pay, Shop Pay, Klarna or a Resin Coatings Direct gift voucher. Payment is taken in full when you order, through Shopify's secure checkout, and all prices are in GBP including VAT. Full Payment Policy

How much does shipping cost?

UK delivery is a flat £9.99 per order, including VAT, for any order size and any UK address. The charge is shown at checkout before you pay, and nothing else is added. We deliver to the UK only. Full Shipping Policy