5kg Heavy Duty Penetrating Epoxy System

Concrete Repair

Penetrating Epoxy Sealer for Weak Screeds & Concrete - 5kg or 10kg

Clear, solvent-free penetrating epoxy sealer and binder for weak screeds and concrete, in 5kg (up to 15-25m²) and 10kg (up to 30-50m²) units.

SKU RCD634

£190.36 incl. VAT

Key features

  • Easy to mix and apply
  • 2-part epoxy system
  • Maximum sealing and binding for weak floors
  • Superb coverage
Size: 5kg | Coverage up to 15-25m²

Product details

Product description

A clear, solvent-free, low-viscosity epoxy resin that acts as a penetrating sealer and binder to strengthen and restore poorly compacted or low-strength screeds and concrete. It penetrates deep into the substrate, filling voids and consolidating loose particles, and is supplied as a two-part unit with pre-weighed resin and activator.

It dries to a transparent finish and is designed as a strengthening layer before epoxy, polyurethane or polyaspartic resin paint systems. By improving the structural integrity of the surface, it gives the following coats the best adhesion and longevity, while its clear finish lets the natural character of the underlying material show through.

Coverage
  • 5kg: up to 15-25m²
  • 10kg: up to 30-50m²

Coverage depends on surface porosity and is for guidance only.

Preparation

Clean the surface thoroughly; concrete should be free from dust and laitance. Remove any flaking old paint and sand or wire brush the surface to create a mechanical key. Mechanical preparation (shot blasting or grinding) is always best; if that is not possible, sanding or concrete etch and clean is a good alternative (etch and clean is only suitable for bare concrete). Make good blow holes and defective concrete with a repair mortar, then sweep and vacuum away all dust and loose material.

Mixing & Application

Apply at an ambient temperature of at least 7°C.

  1. Mix Part A on its own with a paddle on an electric drill for about 1 minute. Add ALL of Part B and mix for another 90 seconds, keeping the paddle submerged to avoid mixing in air, until uniform. All mixed material must be used in one application.
  2. Apply immediately by pouring the mixture onto the damaged, frail or porous substrate at a rate of 3-5m²/kg.
  3. Once the coverage rate is reached, use a squeegee to push the mixture into the substrate and cover the surface evenly; cut in around edges with a brush where needed.
  4. Leave to absorb into the surface for 12-24 hours, depending on conditions.

Pot life is 20 minutes – once mixed, the material starts to cure chemically after this time, so remove it from the tin within this window. It stays workable for up to 30 minutes.

Cure Times
  • Touch dry / re-coat: 8-12 hours at 20°C
  • Foot traffic / traffic: 12-24 hours at 20°C
  • Full chemical cure: 7 days – avoid chemicals, including water, until then
Useful Information
  • Do not split the product. Taking smaller quantities from each tin, even if measured correctly, can cause activation problems.
Please Note
  • Do not apply below 7°C or expose to freezing conditions; temperatures below 20°C slow curing and drying times.
  • Do not expose to chemicals, wash, or allow water to rest on the surface until 7 days after application.
  • Wear suitable PPE such as gloves and safety goggles. If the product gets on skin, wash off immediately with plenty of soap and water, and seek medical advice if discomfort occurs.

Specifications

Size
5kg, 10kg (Part A + Part B)
Appearance
Transparent coating
Composition
Low-viscosity epoxy resin primer, solvent free
Substrates
Bare concrete, screeds
Product Components
Resin (Part A) + Activator (Part B), pre-weighed
Typical Installations
Weak, friable screeds that need support
Consumption Rate
0.2-0.3kg/m²
Coverage
3-5m²/kg – 5kg up to 15-25m², 10kg up to 30-50m² (depending on porosity)
Pot Life @20°C
20 minutes
Working Life
30 minutes
Touch Dry Time @20°C
8-12 hours
Re-coat/Foot-traffic Time @20°C
8-12 hours
Traffic / Drying Time @20°C
12-24 hours
Minimum Temperature
7°C
Application Tools
Squeegee, pouring
Usage Location
Interior
Shelf Life
12 months
Storage Temperature
10 - 25°C

Quote request

Get a quote for this product

Penetrating Epoxy Sealer for Weak Screeds & Concrete - 5kg or 10kg5kg | Coverage up to 15-25m²

We only use your details to reply to this request. See our privacy policy.

Frequently asked questions

What is the return policy?

You can return unused, unopened items in their original sealed packaging within 14 days of delivery, with no restocking fee. Contact us first to arrange the return. You pay return postage if you've changed your mind, and we pay if the item is faulty, damaged or incorrect. Refunds go to your original payment method within 5 working days of us receiving your return. Products made, mixed or tinted to your specification can't be returned unless they're faulty. Full Return & Refund Policy

When will I get my order?

Orders are dispatched within 1–2 working days. Delivery then takes 2–4 working days after dispatch, so the total estimated delivery time is 3–6 working days from order.

Orders placed before 2pm (UK time) on a working day are processed the same day. Orders placed after 2pm, at weekends or on UK bank holidays are processed from the next working day. Working days are Monday to Friday, excluding UK bank holidays.

 Full Shipping Policy

Which payment methods do you accept?

We accept Visa, Mastercard, Maestro, American Express, Diners Club, Discover and UnionPay. You can also pay with Apple Pay, Google Pay, Shop Pay, Klarna or a Resin Coatings Direct gift voucher. Payment is taken in full when you order, through Shopify's secure checkout, and all prices are in GBP including VAT. Full Payment Policy

How much does shipping cost?

UK delivery is a flat £9.99 per order, including VAT, for any order size and any UK address. The charge is shown at checkout before you pay, and nothing else is added. We deliver to the UK only. Full Shipping Policy