12mm Deep Epoxy Crack Repair Filler

Concrete Repair

Epoxy Crack Repair Filler 1kg - Pourable Concrete Crack Sealer

1kg ultra-strong, pourable two-part epoxy crack filler for concrete, brickwork and stone – fills up to 6 metres at 12mm x 12mm.

SKU RCD480

£75.98 incl. VAT

Key features

  • Easy to apply
  • VOC and solvent free
  • Pourable
  • Surface usable in 12-24 hours (at 20°C)
  • Waterproof
  • Superb coverage
Colour: Jet Black
Size: 1kg | Coverage up to 6m at 12mm x 12mm crack

Product details

Product description

An ultra-strong, pourable epoxy resin liquid that penetrates, fills and seals fine cracks in concrete, brickwork and stone. Best suited to pourable or pressure-injection crack repairs, it cures to extremely high strengths that often exceed the surrounding concrete, and the surface is usable in 12-24 hours at 20°C.

Repairing small cracks early can be very cost effective, as cracks can grow over time, weakening the surrounding concrete and becoming a hazard. This filler suits cracks in a wide range of concrete surfaces, including floors, steps, paving, patios, garage floors, roads and driveways, curing harder than the surrounding concrete for a cost-effective, waterproof repair that stands the test of time. DIY friendly, it simply pours in for a quick, professional repair that cures in under 24 hours. VOC and solvent free, it is made in the UK and comes in clear, jet black or grey to look similar to concrete.

Preparation

The concrete should be at least 28 days old and free of laitance, dust, grease, oil and existing coatings, with a base relative humidity of 75% or lower, a minimum strength of 25N/mm² and residual moisture below 6%. Vacuum the area thoroughly to remove any loose material or debris that could make the filler cure unevenly; if the crack is large enough, clean it out with a wire brush. Once the surface is clean, dry and free of debris, the filler can be applied.

Mixing & Application

Apply only when the ambient temperature is at least 7°C.

  1. Pour 100% of Part B into the Part A tin and mix thoroughly with a drill and paddle for at least 90 seconds, until the colour and texture are uniform and the curing agent is fully dispersed. All mixed material must be used in one application.
  2. Pour slowly and evenly into the crack until it is completely filled, aiming for an even fill. Pressure injection can also be used, though suitability may vary case by case.
  3. Allow 12-24 hours to cure fully.

Pot life is approximately 20 minutes – once mixed, the filler starts to cure chemically after this time, so remove it from the tin within this window. It stays workable for up to 40 minutes.

Useful Information
  • Do not split the product. Taking smaller quantities from each tin, even if measured correctly, can cause activation problems.
Please Note
  • Do not apply on new or wet concrete (under 21 days old, or with a residual moisture content of 6% or higher).
  • Do not apply below 7°C or expose to freezing conditions; temperatures below 20°C slow curing and drying times.
  • Do not expose to chemicals, wash, or allow water to rest on the surface until 7 days after application.
  • Not UV stable – do not expose to prolonged sunlight, as it will discolour.
  • Wear suitable PPE such as gloves and safety goggles. If the product gets on skin, wash off immediately with plenty of soap and water, and seek medical advice if discomfort occurs.

Specifications

Size
1kg (whole pack weight, Part A + Part B)
Appearance
Clear, jet black or grey
Composition
Low-viscosity two-part high-strength epoxy resin, VOC and solvent free
Substrates
Bare concrete, asphalts, brickwork, stone
Product Components
Resin (Part A) + Activator (Part B)
Typical Installations
Cracks in garage floors, roads, driveways and other concrete surfaces
Maximum Crack Depth
Up to 2cm
Coverage
Up to 6m per kg at 12mm x 12mm
Pot Life
20 minutes
Working Life
40 minutes
Touch Dry / Re-coat / Foot-traffic Time @20°C: 8-12 hours
Traffic / Drying Time @20°C
12-24 hours
Adhesive Strength
3.9 N/mm²
Minimum Temperature
7°C
Recommended Coats
1
Application Method
Pour or pressure injection
Usage Location
Interior/exterior
Shelf Life
12 months
Storage Temperature
10 - 25°C

Quote request

Get a quote for this product

Epoxy Crack Repair Filler 1kg - Pourable Concrete Crack SealerJet Black / 1kg | Coverage up to 6m at 12mm x 12mm crack

We only use your details to reply to this request. See our privacy policy.

Frequently asked questions

What is the return policy?

You can return unused, unopened items in their original sealed packaging within 14 days of delivery, with no restocking fee. Contact us first to arrange the return. You pay return postage if you've changed your mind, and we pay if the item is faulty, damaged or incorrect. Refunds go to your original payment method within 5 working days of us receiving your return. Products made, mixed or tinted to your specification can't be returned unless they're faulty. Full Return & Refund Policy

When will I get my order?

Orders are dispatched within 1–2 working days. Delivery then takes 2–4 working days after dispatch, so the total estimated delivery time is 3–6 working days from order.

Orders placed before 2pm (UK time) on a working day are processed the same day. Orders placed after 2pm, at weekends or on UK bank holidays are processed from the next working day. Working days are Monday to Friday, excluding UK bank holidays.

 Full Shipping Policy

Which payment methods do you accept?

We accept Visa, Mastercard, Maestro, American Express, Diners Club, Discover and UnionPay. You can also pay with Apple Pay, Google Pay, Shop Pay, Klarna or a Resin Coatings Direct gift voucher. Payment is taken in full when you order, through Shopify's secure checkout, and all prices are in GBP including VAT. Full Payment Policy

How much does shipping cost?

UK delivery is a flat £9.99 per order, including VAT, for any order size and any UK address. The charge is shown at checkout before you pay, and nothing else is added. We deliver to the UK only. Full Shipping Policy