25kg cement-based fillet seal mortar for waterproofing joints

Waterproofing & Tanking

Fillet Seal Mortar 25kg - Fast Setting Cement Mortar for Tanking Joints

25kg fast-setting cement-based fillet seal mortar for wall/floor junctions in waterproofing systems, covering up to 1.4m² (about 10 linear metres) at 20mm.

SKU RCD816

£89.60 incl. VAT

Key features

  • Full surface layers up to 20mm thick
  • Fills cracks and indentations up to 50mm deep in a single application
  • Rapid strength development for quick progress
  • Non-shrinking – sets without cracks
Size: 25kg | Coverage up to 1.4m² (10 linear m) at 20mm Thickness

Product details

Product description

This high-quality, quick-hardening cement-based mortar is designed to form fillet joints at the vulnerable points of waterproofing projects, such as wall-to-floor and wall-to-wall junctions. Typically used with our Cement-Based Tanking Slurry and other specialist waterproofing systems, it gives a seamless transition between horizontal and vertical surfaces and minimises the chance of gaps. It is also an efficient repair mortar for quickly filling and repairing damaged areas and deep mortar joints and levelling rough surfaces.

Coverage

25kg: up to 1.4m², roughly 10 linear metres at a thickness of 20mm. Coverage depends on the porosity and type of substrate.

Preparation

All surfaces must be clean, free from previous coatings, dust, cutting residues, loose material and debris. For localised repairs, cut back the edges of the repair area to a clean, square edge. Dampen dry surfaces so they are moist but not wet, removing any puddles or standing water. Stop active water leaks first with our rapid-setting Waterstop Quick-Set Plug, and treat salt-contaminated substrates with our Salt Inhibitor Primer before tanking or applying fillet seal.

Priming: mix our SBR Additive with clean water at 1:1 by volume and apply by roller, brush or spray. Wait about 30 minutes until tacky.

Mixing & Application
  1. Pour 3.5-4 litres of clean water into a clean mortar tub or mixing vessel.
  2. Using an Electric Mortar Drill & Paddle, slowly add 100% of the powder to avoid dust, gradually increase the speed, and mix for about 3 minutes until uniform and all the powder is incorporated.
  3. Let the mix stand for two minutes, then stir briefly again. If needed, add water slowly for the right consistency – no more than 1 litre extra, as more will reduce strength and waterproofing.
  4. Apply at the base of the wall and form the fillet with a trowel or fillet tool. Full surface layers can be up to 20mm thick, and cracks and indentations up to 50mm deep can be filled in one application, feathering out the edges. Extra coats can go on once the first layer is dry enough to support them.
  5. In high-stress areas at wall/floor joints, use SBR Additive diluted 1:2 with water (by volume) as the gauging solution.

Low-risk areas: once the surface is clean, apply a coat of tanking slurry 100mm up the wall and 100mm across the floor over the joint. While it is still tacky, apply the fillet seal and smooth it into a coved fillet across the junction. Allow at least one hour to dry before further coatings.

High-risk areas: cut a 20mm wide x 20mm deep channel at the base of the wall, extending into the wall if possible. Once clean, apply tanking slurry 100mm up the wall, across the channel and 100mm onto the floor. While still tacky, fill the channel and area with fillet seal, shaping a smooth curve over the junction. Allow at least one hour to dry before further coatings.

Cure Times

As a cement-based mortar it dries like concrete and must not dry too quickly, or it may crack. Outdoors in warm or windy conditions, mist spray to reduce moisture loss.

Wear appropriate PPE such as gloves and safety goggles. If the product contacts skin, wash it off immediately with plenty of soap and water. If swallowed, immediately call a poison centre or doctor. If in eyes, rinse cautiously with water for several minutes, removing contact lenses if present and easy to do, and continue rinsing. Seek medical advice if discomfort occurs.

Please Note
  • Do not re-temper stiffened material.
  • Do not apply on frost-filled surfaces, or below 5°C or above 25°C.
  • Lower temperatures can extend working and setting times; higher temperatures shorten them.

Specifications

Size
25kg bucket
Appearance
Loose grey powder, mixes to a robust mortar
Coverage
Up to 1.4m² – roughly 10 linear metres – at 20mm thickness
Water
3.5-4 litres per 25kg
Layer Thickness
Full surface layers up to 20mm; cracks and indentations up to 50mm deep in one application
Initial Set (at 20°C)
60 minutes
Working Time (at 20°C)
Up to 30 minutes
Application Temperature
5°C to 25°C
Shelf Life
12 Months

Quote request

Get a quote for this product

Fillet Seal Mortar 25kg - Fast Setting Cement Mortar for Tanking Joints

We only use your details to reply to this request. See our privacy policy.

Frequently asked questions

What is the return policy?

You can return unused, unopened items in their original sealed packaging within 14 days of delivery, with no restocking fee. Contact us first to arrange the return. You pay return postage if you've changed your mind, and we pay if the item is faulty, damaged or incorrect. Refunds go to your original payment method within 5 working days of us receiving your return. Products made, mixed or tinted to your specification can't be returned unless they're faulty. Full Return & Refund Policy

When will I get my order?

Orders are dispatched within 1–2 working days. Delivery then takes 2–4 working days after dispatch, so the total estimated delivery time is 3–6 working days from order.

Orders placed before 2pm (UK time) on a working day are processed the same day. Orders placed after 2pm, at weekends or on UK bank holidays are processed from the next working day. Working days are Monday to Friday, excluding UK bank holidays.

 Full Shipping Policy

Which payment methods do you accept?

We accept Visa, Mastercard, Maestro, American Express, Diners Club, Discover and UnionPay. You can also pay with Apple Pay, Google Pay, Shop Pay, Klarna or a Resin Coatings Direct gift voucher. Payment is taken in full when you order, through Shopify's secure checkout, and all prices are in GBP including VAT. Full Payment Policy

How much does shipping cost?

UK delivery is a flat £9.99 per order, including VAT, for any order size and any UK address. The charge is shown at checkout before you pay, and nothing else is added. We deliver to the UK only. Full Shipping Policy