Brewery Floor Coating – Epoxy Resin, 1–10kg

Floor Paint

Brewery Floor Paint Epoxy Coating 1kg to 10kg - Chemical & Sugar Resistant

Two-part epoxy brewery floor coating in 1kg, 2.5kg, 5kg and 10kg packs – ultra-durable, chemical and sugar resistant protection for concrete floors.

SKU RCD1368

£87.98 incl. VAT

Key features

  • Ultra durable
  • Chemical resistant
  • Sugar resistant
  • Easy to clean and maintain
  • Antibacterial and anti-microbial
  • Surface usable in 24 hours
  • 17-20m² coverage per 5kg
  • Low VOC and 100% solvent free
Colour: Light Grey
Size: 1kg | Coverage 3-4m² per coat

Product details

Product description

This two-part epoxy paint has been designed, tested and manufactured specifically for the brewing and micro-brewing industry. Ultra-durable and spill resistant, it gives concrete floors in brewing units a strong layer of protection, and its easy-to-clean formula saves a great deal of maintenance time, keeping your brewing unit in excellent condition.

It produces a smooth, high gloss finish in a wide range of colours, letting you bring your brewery unit to life while protecting the concrete and speeding up daily care. Although made primarily for breweries, its high durability also makes it a good choice for food manufacturers and other liquid manufacturing spaces. For a perfect, glossy finish, use of a primer is recommended.

Coverage
  • 1kg: 3-4m²
  • 2.5kg: 8-10m²
  • 5kg: 17-20m²
  • 10kg: 35-40m²

Coverage rates are per coat; in most cases 2 coats are advised. Pack weights are for the whole pack (Part A and Part B combined).

Preparation

Make sure the concrete is clean and free from dust, laitance and oil. Remove old paint finishes if they are flaking at all, and sand the surface to create a texture (a mechanical key). Mechanical preparation by shot-blasting or grinding is always advisable for best results; if that is not possible, sanding or Concrete Etch and Clean is a good alternative (Etch and Clean is only suitable for bare concrete). Make good pinholes and defective concrete with a repair mortar. Steel surfaces should be shot blasted or grit blasted to a nominal Sa 2.5 Swedish standard. Once the surface has been abraded, thoroughly sweep and vacuum away any remaining dust or contaminants.

Priming

A relevant primer should be used, especially on new or oil-contaminated concrete. A typical system is 1 coat of primer and 2 coats of this coating.

Mixing & Application

Apply when the ambient temperature is at least 7°C.

  1. Gently stir Part A on its own with a mixing paddle on an electric drill to disperse the pigment, then add ALL of Part B and mix until the colour and texture are uniform and the curing agent has fully dispersed, keeping the paddle submerged to avoid mixing air into the unit.
  2. Pour the entire contents of the tin into a plastic paint scuttle or tray.
  3. Immediately begin applying with a nylon-bonded, resin-suitable epoxy roller, cross-rolling flat areas for an even, smooth finish and moving down the floor until complete. Large areas may need several people.
  4. Use a brush around the edges to cut in (a second pair of hands can help here).
  5. Re-coat as soon as the first coat has started curing and is no longer tacky to the touch. Apply the first coat no later than 24 hours after the primer has cured or is dry to touch, and the second coat no later than 24 hours after the first has cured.
  6. The cured final coat is fine for foot traffic.

The pot life is 20 minutes: once mixed, the paint starts to chemically cure after this time, so remove it from the tin within this window; it stays workable on the floor for up to 40 minutes. Pot life is the time to harden in the pot after the hardener is added; working time is the time available to apply the product before it becomes unworkable. Once mixed, 100% of the material must be used in one application. Wear appropriate PPE such as gloves and protective safety goggles; if the product contacts skin, wash off immediately with plenty of soap and water and seek medical advice if discomfort occurs.

Cure Times
  • Re-coat time: 16-24 hours at 10°C; 8-12 hours at 20°C
  • Car traffic time: 24-48 hours at 10°C; 12-24 hours at 20°C
  • Industrial traffic time: 72 hours at 10°C; 48 hours at 20°C
  • Full chemical cure: 7 days at 20°C
Useful Information
  • Use a fresh roller sleeve for each coat – two coats require two roller sleeves.
  • This product is NOT UV stable and can discolour with regular sunlight. For areas with plenty of repeated sunlight, coat with a coloured UV-stable finish such as Chemical Resistant UVR Floor Paint.
  • This product should NOT be split. Taking smaller quantities from each tin, even if measured correctly, may cause problems with activation.
  • This product is NOT self-levelling.
  • For a clear epoxy coating, see our Clear Epoxy Floor Paint.
Please Note
  • Do not apply on new or wet concrete (under 28 days old or with a residual moisture content of 6% or higher). The concrete must have a damp proof membrane beneath it for epoxy coatings to be applied.
  • Do not apply below 7°C or expose to freezing conditions; temperatures below 20°C will slow curing and drying times.
  • Do not expose to chemicals, wash or allow water to rest on the surface until 7 days after application (full chemical cure).

Specifications

Size
1kg, 2.5kg, 5kg, 10kg
Colours
Light Grey, Mid Grey (Silver Grey), Dark Grey (Slate Grey), Cobalt Blue, Light Ivory, Sky Blue, Leaf Green, Fern Green, Tomato Red, Golden Yellow, Vermillion, Jet Black, White
Appearance
Smooth, high gloss finish
Composition
100% solids
Substrates
Bare concrete, wood, screeds, steel
Product Components
Resin (Part A) + Activator (Part B)
Typical Installations
Brewery, micro-brewery, chemical plants, liquid manufacturing, toilet areas etc.
Solvent Content
Solvent free, low VOC
Pot Life
20 minutes
Working Life
40 minutes
Re-coat/Foot-traffic Time (at 20°C)
8-12 hours
Drying Time (at 20°C)
12-24 hours
Thickness
250 microns per coat
Consumption Rate
0.25-0.30kg/m²
Coverage
Up to 4m² per kg
Recommended Coats
2
Minimum Temperature
7°C
Application Tools
Epoxy roller sleeve and frame, brushes
Usage Location
Interior
Shelf Life
12 months
Storage Temperature
10 - 25°C

Quote request

Get a quote for this product

Brewery Floor Paint Epoxy Coating 1kg to 10kg - Chemical & Sugar ResistantLight Grey / 1kg | Coverage 3-4m² per coat

We only use your details to reply to this request. See our privacy policy.

Frequently asked questions

What is the return policy?

You can return unused, unopened items in their original sealed packaging within 14 days of delivery, with no restocking fee. Contact us first to arrange the return. You pay return postage if you've changed your mind, and we pay if the item is faulty, damaged or incorrect. Refunds go to your original payment method within 5 working days of us receiving your return. Products made, mixed or tinted to your specification can't be returned unless they're faulty. Full Return & Refund Policy

When will I get my order?

Orders are dispatched within 1–2 working days. Delivery then takes 2–4 working days after dispatch, so the total estimated delivery time is 3–6 working days from order.

Orders placed before 2pm (UK time) on a working day are processed the same day. Orders placed after 2pm, at weekends or on UK bank holidays are processed from the next working day. Working days are Monday to Friday, excluding UK bank holidays.

 Full Shipping Policy

Which payment methods do you accept?

We accept Visa, Mastercard, Maestro, American Express, Diners Club, Discover and UnionPay. You can also pay with Apple Pay, Google Pay, Shop Pay, Klarna or a Resin Coatings Direct gift voucher. Payment is taken in full when you order, through Shopify's secure checkout, and all prices are in GBP including VAT. Full Payment Policy

How much does shipping cost?

UK delivery is a flat £9.99 per order, including VAT, for any order size and any UK address. The charge is shown at checkout before you pay, and nothing else is added. We deliver to the UK only. Full Shipping Policy