Polyurea Joint Sealer 5 Min Cure Flexible

Joint Sealants

Polyurea Joint Sealant 400ml Dual Cartridge - 5 Minute Cure, -25°C

400ml dual-cartridge flexible polyurea joint sealant with an initial cure of around 5 minutes, covering approx. 3.8m of 5mm x 20mm joint.

SKU RCD426

£111.18 incl. VAT

Key features

  • Easy gun application
  • Quick initial cure – around 5 minutes
  • Low VOC and solvent free
  • Cures in temperatures from -25°C to +54°C
  • Great chemical resistance
  • Low viscosity for deep penetration into cracks and joints
Size: 400ml Dual Cartridge | Coverage approx. 3.8m at 5mm x 20mm joint

Product details

Product description

A high-quality, flexible polyurea sealer that easily fills joints and cracks in concrete and other surfaces. Its fast cure makes it ideal where a quick turnaround is needed – initial cure can be as quick as 5 minutes, allowing light traffic within 1 hour. It works well in adverse temperatures and is highly flexible, allowing slab movement while staying strong enough to prevent spalled joints under heavy pressure.

Once cured it is impervious to moisture, self-levelling and very hard-wearing, and its low viscosity gives deep penetration into cracks and joints. It is low VOC, solvent free and offers great chemical resistance. Typical uses include cracked concrete and spalled floor joints, inside and out, and sealing concrete expansion joints in loading bays, freezer storage rooms and production areas – ideal for fast turnarounds and highly demanding conditions. It must be applied with a 1:1 dual cartridge application gun.

Coverage

One 400ml dual cartridge covers roughly 3800mm of linear length for a 5mm x 20mm joint. Exact coverage depends on the porosity, type and condition of the existing surface.

Preparation

Remove all dirt, oil, dust, foreign contaminants and laitance to ensure a good bond to the concrete. For spalled concrete or pop-outs, remove all loose or unsound concrete with a stiff wire brush or twisted wire wheel on a grinder; clean cracks the same way or with a diamond blade saw. Then remove all dust and debris with an industrial vacuum and oil-free compressed air. All surfaces must be clean and dry before application.

Application

Environment: condition the sealant to room temperature (16°C to 27°C) before use, and keep any sand used dry and at room temperature. Warm material, hot concrete or a warm environment speeds up curing; cold material, cold concrete or a cold environment slows it. Heat cold concrete to remove any visible frost before application.

Readying cartridges:

  1. Shake the cartridge well, then let it stand for one minute so trapped air can disperse.
  2. Insert it into a dual-component 200ml x 200ml manual dispenser with a 1:1 mix ratio.
  3. Remove the retaining nut to open the cartridge – keep it, as it can be refitted to save a part-used cartridge.
  4. Holding the cartridge at a slight upward angle, slowly dispense a little material into a disposable container until both parts flow evenly and the colour is consistent.
  5. Still holding it angled upwards, fit the flow control and mixing nozzle. Point the nozzle straight up and slowly gun material through until it reaches the tip, then point upwards at 45° and dispense one stroke into a disposable container.

Cracks: gun the sealant directly into the crack, letting it penetrate, and top off as needed. Kiln-dried medium-grade (30 mesh) silica sand or dry floor grindings can be sprinkled onto the wet sealant to add texture and match the surrounding concrete. Keep the material flowing so it does not harden in the nozzle. Once mixed, it is tack free in 10 minutes at 24°C.

Joints: prepare the joint with a square edge, using a foam backing rod if the cut is deep. Gun the sealant directly into the joint, keeping it flowing so it does not harden in the nozzle. Kiln-dried sand can then be sprinkled on top to match the surrounding area if required.

Please Note
  • Do not apply to wet substrates – the product may foam.
  • Although UV stabilised, it may discolour over time; its physical properties are not affected.
  • Danger: two-part product. Causes skin irritation, may cause an allergic skin reaction, and may cause allergy or asthma symptoms or breathing difficulties if inhaled.
  • If on skin, wash immediately with plenty of soap and water. If inhaled, move the person to fresh air and keep them comfortable for breathing. Seek medical advice if there is any discomfort.

Specifications

Size
400ml dual cartridge
Coverage
Approx. 3800mm linear length for a 5mm x 20mm joint
Appearance
Smooth, self-levelling mid grey sealant
Composition
Two-component flexible polyurea
Durability
Very heavy-duty jointing
Ambient Temperature
-25°C to +54°C during application
Product Components
Dual-component cartridge
Typical Installations
Sealing concrete expansion joints in loading bays, freezer storage rooms, production zones etc.
Mix Ratio (Part A
Part B): 1:1 by volume
Final Colour
Mid grey
Pot Life
Under 30 seconds
Gel Time at 24°C
30-90 seconds
Tack-free Time at 24°C
Under 10 minutes
Initial Cure
Around 5 minutes; light traffic within 1 hour
Shore D Hardness
70 - 80
Tensile Strength at 7 Days
1000 psi
Bond Strength
500 psi
UV Stability
Stabilised
Shelf Life
1 year in original unopened packaging

Quote request

Get a quote for this product

Polyurea Joint Sealant 400ml Dual Cartridge - 5 Minute Cure, -25°C

We only use your details to reply to this request. See our privacy policy.

Frequently asked questions

What is the return policy?

You can return unused, unopened items in their original sealed packaging within 14 days of delivery, with no restocking fee. Contact us first to arrange the return. You pay return postage if you've changed your mind, and we pay if the item is faulty, damaged or incorrect. Refunds go to your original payment method within 5 working days of us receiving your return. Products made, mixed or tinted to your specification can't be returned unless they're faulty. Full Return & Refund Policy

When will I get my order?

Orders are dispatched within 1–2 working days. Delivery then takes 2–4 working days after dispatch, so the total estimated delivery time is 3–6 working days from order.

Orders placed before 2pm (UK time) on a working day are processed the same day. Orders placed after 2pm, at weekends or on UK bank holidays are processed from the next working day. Working days are Monday to Friday, excluding UK bank holidays.

 Full Shipping Policy

Which payment methods do you accept?

We accept Visa, Mastercard, Maestro, American Express, Diners Club, Discover and UnionPay. You can also pay with Apple Pay, Google Pay, Shop Pay, Klarna or a Resin Coatings Direct gift voucher. Payment is taken in full when you order, through Shopify's secure checkout, and all prices are in GBP including VAT. Full Payment Policy

How much does shipping cost?

UK delivery is a flat £9.99 per order, including VAT, for any order size and any UK address. The charge is shown at checkout before you pay, and nothing else is added. We deliver to the UK only. Full Shipping Policy