5kg Antibacterial Wall Coating - Antimicrobial Protection

Masonry & Wall Paint

Antibacterial Epoxy Wall Coating 2.5kg or 5kg - 99.9% Effective vs MRSA

Two-part epoxy antibacterial wall coating, independently tested to ISO 22196, in 2.5kg and 5kg packs covering up to 15m² or 30m² per coat.

SKU RCD539

£122.60 incl. VAT

Key features

  • Easy to clean
  • >99.9% effective against E.coli, Staph aureus and MRSA
  • Professional finish
  • Superb coverage rates
  • Surface usable in 24 hours
  • Solvent free
Colour: Light Grey
Size: 2.5kg | Coverage up to 15m² per coat

Product details

Product description

This epoxy antibacterial wall coating has been independently tested to ISO 22196 and accredited by a leading UK provider of antibacterial agents. It is more than 99.9% effective against E.coli, Staph aureus and the superbug MRSA, making it ideal for walls in hospital wards, hygiene-control areas, schools and other sanitary environments. It adheres to most substrates, including concrete, wood and metal.

The coating gives fast, effective antimicrobial protection for its effective lifetime, helping keep surroundings hygienic and reducing the risk of cross-contamination. Whereas an antibacterial coating prevents the growth of bacteria, this antimicrobial coating goes further, destroying bacteria as well as a wide range of microbes such as fungi and mould. It minimises staining and bad odours, is easy to clean and maintain, and is up to 5x thicker than cheaper alternatives for a highly durable finish. Made in the UK, it is solvent free and comes in a range of colours; typical applications also include garages, factories, breweries, industrial storage areas and basements.

Coverage
  • 2.5kg: up to 15m² per coat
  • 5kg: up to 30m² per coat

In most cases 2 coats are advised.

Preparation

Make sure the surface is clean and free from dust, laitance, oil and any other contaminants. Remove any flaking old paint and sand the surface to create a mechanical key – mechanical treatment is preferred. Make good defective surfaces with a suitable repair product. Use a suitable primer, especially on damp or oil-contaminated surfaces. Steel should be shot or grit blasted to a nominal Sa 2.5 (Swedish standard). After abrading, thoroughly sweep and vacuum away all dust and contaminants.

Mixing & Application

Apply at an ambient temperature of at least 7°C.

  1. Mix Part A on its own with a paddle on an electric drill for 1-2 minutes to disperse the pigment. Add ALL of Part B and mix for another 90 seconds, keeping the paddle submerged to avoid mixing in air, until the colour and texture are uniform.
  2. Pour the entire contents into a plastic paint scuttle or tray – all mixed material must be used in one application.
  3. Begin applying immediately with a nylon-bonded, resin-suitable epoxy roller sleeve, cross-rolling for an even, smooth finish. Large areas may need several people.
  4. Cut in around the edges with a brush – a second pair of hands helps here.
  5. Re-coat once the first coat is no longer tacky – 4-6 hours at 20°C or 12-16 hours at 10°C. A typical system is 1 coat of primer and 2 coats of coating, each applied within 24 hours of the previous coat curing.
  6. The cured final coat is fine for contact, but do not introduce chemicals, including water and cleaning products, for the first 7 days (full chemical cure).

Pot life is 40-60 minutes – once mixed, the coating starts to cure chemically after this time, so remove it from the tin within this window. It stays workable for 60-70 minutes.

Cure Times
  • Re-coat: 12-16 hours at 10°C, 4-6 hours at 20°C
  • Car traffic: 36-48 hours at 10°C, 24 hours at 20°C
  • Industrial traffic: 72 hours at 10°C, 48 hours at 20°C
  • Full chemical cure: 7 days at 20°C
Useful Information
  • Use one roller sleeve per coat – two coats need two roller sleeves.
  • Do not split the product. Taking smaller quantities from each tin, even if measured correctly, can cause activation problems.
Please Note
  • Do not apply on new or wet concrete (under 28 days old, or with a residual moisture content of 6% or higher). Concrete must have a damp proof membrane beneath it for epoxy coatings to be applied.
  • Do not apply below 7°C or expose to freezing conditions; temperatures below 20°C slow curing and drying times.
  • Do not expose to chemicals, wash, or allow water to rest on the surface until 7 days after application.
  • Not UV stable – do not expose to prolonged sunlight, as it will discolour.
  • Wear suitable PPE such as gloves and safety goggles. If the product gets on skin, wash off immediately with plenty of soap and water, and seek medical advice if discomfort occurs.

Specifications

Size
2.5kg, 5kg (whole pack weight, Part A + Part B)
Appearance
Tough, semi-gloss finish
Composition
Two-part epoxy with antimicrobial properties, solvent free
Substrates
Bare concrete, wood, screeds, steel
Product Components
Resin (Part A) + Activator (Part B)
Typical Installations
Anywhere needing antimicrobial surfaces, hygiene and infection control
Antimicrobial Performance
≥99.9% kill rate for MRSA and bacteria (tested to ISO 22196)
Coverage
Up to 15m² per 2.5kg, up to 30m² per 5kg (per coat)
Consumption Rate
~0.15kg/m²
Thickness
100 microns per coat
Pot Life
40-60 minutes
Working Life
60-70 minutes
Re-coat/Foot-traffic Time (at 20°C)
4-6 hours
Drying Time (at 20°C)
24 hours
Minimum Temperature
7°C
Recommended Coats
2
Application Tools
Epoxy roller sleeve and frame, brush
Usage Location
Interior
Shelf Life
12 months
Storage Temperature
10 - 25°C
Colours
Light Grey, Dark Grey (Slate Grey), Cobalt Blue, Light Ivory, Sky Blue, Leaf Green, Fern Green, Tomato Red, Golden Yellow, Jet Black, White, Mid Grey, Traffic Red

Quote request

Get a quote for this product

Antibacterial Epoxy Wall Coating 2.5kg or 5kg - 99.9% Effective vs MRSALight Grey / 2.5kg | Coverage up to 15m² per coat

We only use your details to reply to this request. See our privacy policy.

Frequently asked questions

What is the return policy?

You can return unused, unopened items in their original sealed packaging within 14 days of delivery, with no restocking fee. Contact us first to arrange the return. You pay return postage if you've changed your mind, and we pay if the item is faulty, damaged or incorrect. Refunds go to your original payment method within 5 working days of us receiving your return. Products made, mixed or tinted to your specification can't be returned unless they're faulty. Full Return & Refund Policy

When will I get my order?

Orders are dispatched within 1–2 working days. Delivery then takes 2–4 working days after dispatch, so the total estimated delivery time is 3–6 working days from order.

Orders placed before 2pm (UK time) on a working day are processed the same day. Orders placed after 2pm, at weekends or on UK bank holidays are processed from the next working day. Working days are Monday to Friday, excluding UK bank holidays.

 Full Shipping Policy

Which payment methods do you accept?

We accept Visa, Mastercard, Maestro, American Express, Diners Club, Discover and UnionPay. You can also pay with Apple Pay, Google Pay, Shop Pay, Klarna or a Resin Coatings Direct gift voucher. Payment is taken in full when you order, through Shopify's secure checkout, and all prices are in GBP including VAT. Full Payment Policy

How much does shipping cost?

UK delivery is a flat £9.99 per order, including VAT, for any order size and any UK address. The charge is shown at checkout before you pay, and nothing else is added. We deliver to the UK only. Full Shipping Policy