2cm Deep Asphalt Crack Repair Compound

Driveway & Patio

Asphalt Crack Repair Filler 1kg Black - Pourable Epoxy, Cracks to 2cm

1kg jet black, pourable two-part epoxy crack filler for asphalt and tarmac cracks up to 2cm deep – fills up to 6 metres at 12mm x 12mm.

SKU RCD428

£62.78 incl. VAT

Key features

  • Easy to apply
  • Sets stronger than concrete
  • Can be applied over a wide range of temperatures
  • Ideal for asphalt cracks up to 2cm deep
  • 100% epoxy formula – solvent free
  • Waterproof
Colour: Jet Black
Size: 1kg | Coverage up to 6m at 12mm x 12mm crack

Product details

Product description

An ultra-strong, pourable epoxy resin liquid that penetrates and seals fine asphalt cracks, with excellent waterproofing and sealing properties for roads, car parks, driveways and other surfaces. It is easy to apply, sets stronger than concrete and can be used over a wide range of temperatures.

It is ideal for filling cracks and holes up to 2cm deep in damaged tarmac, asphalt and bitumen surfaces – for larger holes, use heavy duty asphalt repair mortar. With good slip-resistant properties, it is suitable for roads and areas used by heavy vehicles. Best applied by pouring (pressure injection is also possible), it cures to extremely high strengths that often exceed the surrounding material. The 100% epoxy, VOC- and solvent-free formula is jet black to look like asphalt or tarmac.

Preparation

The surface should be free of laitance, dust, grease, oil and existing coatings. Vacuum the crack to remove any loose material or debris that could make the filler set unevenly; if the crack is large enough, clean it out with a wire brush. For a cleaner result, angle grind the crack. If you suspect the crack runs through the full depth, add some kiln-dried silica sand to the bottom of the crack to form a bund. The base should have a relative humidity of 75% or lower and residual moisture below 6%.

Mixing & Application

Apply at an ambient temperature of at least 7°C.

  1. Pour 100% of Part B into the Part A tin and mix thoroughly with a drill and paddle for at least 90 seconds, until the colour and texture are uniform and the curing agent is fully dispersed. All mixed material must be used in one application.
  2. Pour slowly and evenly into the crack until it is filled, aiming for an even fill. Pressure injection can also be used, though results may vary case by case.
  3. Allow 12-24 hours to cure fully.

Pot life is 20 minutes – once mixed, the filler starts to cure chemically after this time, so remove it from the tin within this window. It stays workable for up to 40 minutes.

Useful Information
  • Do not split the product. Taking smaller quantities from each tin, even if measured correctly, can cause activation problems.
Please Note
  • Do not apply on new or wet surfaces (under 21 days old, or with a residual moisture content of 6% or higher).
  • Do not apply below 7°C or expose to freezing conditions; temperatures below 20°C slow curing and drying times.
  • Do not expose to chemicals, wash, or allow water to rest on the surface until 7 days after application.
  • Not UV stable – do not expose to prolonged sunlight, as it will discolour.
  • Wear suitable PPE such as gloves and safety goggles. If the product gets on skin, wash off immediately with plenty of soap and water, and seek medical advice if discomfort occurs.

Specifications

Size
1kg (whole pack weight, Part A + Part B)
Appearance
Black, tarmac-like
Composition
Low-viscosity, high-strength 100% epoxy resin, VOC and solvent free
Substrates
Asphalt, macadam, tarmac and other blacktop surfaces
Product Components
Resin (Part A) + Activator (Part B)
Typical Installations
Penetrating and sealing fine asphalt cracks
Maximum Crack Depth
2cm
Coverage
Up to 6m per kg at 12mm x 12mm
Pot Life
20 minutes
Working Life
40 minutes
Touch Dry / Re-coat / Foot-traffic Time @20°C: 8-12 hours
Traffic / Drying Time @20°C
12-24 hours
Adhesive Strength
3.9 N/mm²
Minimum Temperature
7°C
Recommended Coats
1
Application Method
Pour or pressure injection
Usage Location
Interior/exterior
Shelf Life
12 months
Storage Temperature
10 - 25°C

Quote request

Get a quote for this product

Asphalt Crack Repair Filler 1kg Black - Pourable Epoxy, Cracks to 2cm

We only use your details to reply to this request. See our privacy policy.

Frequently asked questions

What is the return policy?

You can return unused, unopened items in their original sealed packaging within 14 days of delivery, with no restocking fee. Contact us first to arrange the return. You pay return postage if you've changed your mind, and we pay if the item is faulty, damaged or incorrect. Refunds go to your original payment method within 5 working days of us receiving your return. Products made, mixed or tinted to your specification can't be returned unless they're faulty. Full Return & Refund Policy

When will I get my order?

Orders are dispatched within 1–2 working days. Delivery then takes 2–4 working days after dispatch, so the total estimated delivery time is 3–6 working days from order.

Orders placed before 2pm (UK time) on a working day are processed the same day. Orders placed after 2pm, at weekends or on UK bank holidays are processed from the next working day. Working days are Monday to Friday, excluding UK bank holidays.

 Full Shipping Policy

Which payment methods do you accept?

We accept Visa, Mastercard, Maestro, American Express, Diners Club, Discover and UnionPay. You can also pay with Apple Pay, Google Pay, Shop Pay, Klarna or a Resin Coatings Direct gift voucher. Payment is taken in full when you order, through Shopify's secure checkout, and all prices are in GBP including VAT. Full Payment Policy

How much does shipping cost?

UK delivery is a flat £9.99 per order, including VAT, for any order size and any UK address. The charge is shown at checkout before you pay, and nothing else is added. We deliver to the UK only. Full Shipping Policy