{"product_id":"epoxy-primer-2-part-system-for-enhanced-adhesion","title":"Epoxy Floor Primer 2-Part Solvent Free Clear Sealer - 1kg to 10kg","description":"\u003cp\u003e\u003cstrong\u003eLow viscosity, solvent-free two-part epoxy primer that seals surfaces before painting, available in 1kg, 2.5kg, 5kg and 10kg kits.\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis high-quality, general purpose epoxy floor primer makes an effective base coat for a wide range of surfaces before painting. Its low viscosity industrial twin pack formulation absorbs deeply into the existing substrate, cures stronger than concrete and seals effectively, giving a strong, durable bond and leaving a clear finish. It ensures resin paint systems adhere to concrete and other surfaces, and improves the coverage and quality of finish for epoxy paints and polyurethane resin systems.\u003c\/p\u003e\u003cp\u003ePriming before applying \u003ca href=\"\/products\/epoxy-resin-floor-paint-multiple-colours-sizes\"\u003eEpoxy Floor Paint\u003c\/a\u003e matters for three reasons:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eIt creates a strong bond between the paint and the substrate, so the paint adheres well and is less likely to peel or flake over time – especially important in high-traffic areas or where the surface sees regular wear and tear.\u003c\/li\u003e\n\u003cli\u003eIt helps stop moisture penetrating the surface, which can damage the substrate and compromise the paint – important where there is a risk of water damage, such as garages or warehouses.\u003c\/li\u003e\n\u003cli\u003eIt gives a smooth, even base coat that improves the coverage and quality of the top coat, for a professional, uniform finish with a high level of protection against wear.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSize: 1kg, 2.5kg, 5kg, 10kg\u003c\/li\u003e\n\u003cli\u003eAppearance: Clear\u003c\/li\u003e\n\u003cli\u003eComposition: Epoxy Resin of Low Viscosity\u003c\/li\u003e\n\u003cli\u003eSubstrates: Bare Concrete, Wood, Screeds, Steel\u003c\/li\u003e\n\u003cli\u003eProduct Components: Resin (Part A) + Activator (Part B) – 2 pack system\u003c\/li\u003e\n\u003cli\u003eTypical Installations: Base coat for installations such as garages, factories, warehouses, showrooms, etc.\u003c\/li\u003e\n\u003cli\u003eSolvent Content: Solvent Free\u003c\/li\u003e\n\u003cli\u003eConsumption Rate: 0.2-0.3kg\/m²\u003c\/li\u003e\n\u003cli\u003eCoverage: 5m²\/kg\u003c\/li\u003e\n\u003cli\u003ePot Life (at 20°C): 20 Minutes\u003c\/li\u003e\n\u003cli\u003eWorking Life: 30 Minutes\u003c\/li\u003e\n\u003cli\u003eTouch Dry Time (at 20°C): 8-12 Hours\u003c\/li\u003e\n\u003cli\u003eRe-coat Time (at 20°C): 8-12 Hours\u003c\/li\u003e\n\u003cli\u003eTraffic\/Drying Time (at 20°C): 12-24 Hours\u003c\/li\u003e\n\u003cli\u003eApplication Tools: Roller, Brush\u003c\/li\u003e\n\u003cli\u003eUsage Location: Interior\u003c\/li\u003e\n\u003cli\u003eShelf Life: 12 Months\u003c\/li\u003e\n\u003cli\u003eStorage Temperature: 10 - 25°C\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eEasy to mix and apply\u003c\/li\u003e\n\u003cli\u003eTwo part epoxy (includes Part A and Part B)\u003c\/li\u003e\n\u003cli\u003eExcellent adhesion and sealing qualities\u003c\/li\u003e\n\u003cli\u003eSuperb coverage\u003c\/li\u003e\n\u003cli\u003eSolvent free\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eCoverage\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e1kg: 5m²\u003c\/li\u003e\n\u003cli\u003e2.5kg: 12.5m²\u003c\/li\u003e\n\u003cli\u003e5kg: 25m²\u003c\/li\u003e\n\u003cli\u003e10kg: 50m²\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eCoverage rates depend on the porosity of the surface.\u003c\/p\u003e\u003ch3\u003ePreparation\u003c\/h3\u003e\u003cp\u003eClean the surface to be primed thoroughly. Old paint finishes should be removed if they are flaking at all, and the surface sanded to create a texture (a mechanical key). For floors, mechanical preparation (shot-blasting or grinding) always gives the best results; if that is not possible, sanding or our \u003ca href=\"\/products\/5l-concrete-etch-and-clean-preparation-liquid\"\u003eConcrete Etch and Clean\u003c\/a\u003e is a good alternative (Etch and Clean is only suitable for bare concrete). Concrete should be free from dust and laitance through sanding or wire brushing, and blow holes and defective concrete should be made good with a repair mortar. Once fully abraded, sweep and vacuum away all remaining dust, loose material and contaminants.\u003c\/p\u003e\u003ch3\u003eMixing \u0026amp; Application\u003c\/h3\u003e\u003cp\u003eThe ambient temperature should be at least 7°C when applying.\u003c\/p\u003e\u003col\u003e\n\u003cli\u003eMix Part A on its own with a mixing paddle on an electric drill for about 1 minute, then add ALL of Part B and mix for another 90 seconds until a uniform colour is achieved, keeping the paddle in suspension to avoid mixing air into the unit.\u003c\/li\u003e\n\u003cli\u003ePour the entire contents of the tin into a plastic paint scuttle or tray.\u003c\/li\u003e\n\u003cli\u003eBegin applying immediately with a nylon-bonded, resin-suitable roller or brush, using a consistent method. Cross roll floor areas for an even application with minimal marking, and use several people on large areas.\u003c\/li\u003e\n\u003cli\u003eUse a brush around the edges to cut in (a second pair of hands is useful for this stage).\u003c\/li\u003e\n\u003cli\u003eRe-coat as soon as the first coat has started curing and is no longer tacky to touch.\u003c\/li\u003e\n\u003cli\u003eThe cured final coat is fine for foot traffic and ready for further coats of primer or your first coat of paint.\u003c\/li\u003e\n\u003c\/ol\u003e\u003cp\u003eThe pot life is 20 minutes: once the parts are mixed the product starts to chemically cure, so remove it from the tin within this window. 100% of the product must be used in a single application and cannot be stored for later use. Pot life is the time to harden in the pot after the hardener is added; working time is the time available to apply the product before it becomes unworkable.\u003c\/p\u003e\u003cp\u003eWear appropriate PPE such as gloves and safety goggles. If the product contacts skin, wash it off immediately with plenty of soap and water, and seek medical advice if discomfort occurs.\u003c\/p\u003e\u003ch3\u003eUseful Information\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eUse one roller sleeve per coat – two coats need two roller sleeves.\u003c\/li\u003e\n\u003cli\u003eThis product should NOT be split. Taking smaller quantities from each tin, even if measured correctly, may cause problems with activation.\u003c\/li\u003e\n\u003cli\u003eThis product is NOT self levelling.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003ePlease Note\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDo not apply at temperatures below 7°C and do not expose to freezing conditions.\u003c\/li\u003e\n\u003cli\u003eTemperatures below 20°C will slow curing and drying times.\u003c\/li\u003e\n\u003cli\u003eDo not expose to chemicals, wash, or allow water to rest on the surface until 7 days after application.\u003c\/li\u003e\n\u003cli\u003eDo not apply to wet or uncured concrete.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Resin Coatings Direct","offers":[{"title":"1kg | Coverage 5m²","offer_id":58122236428670,"sku":"RCD648","price":97.32,"currency_code":"GBP","in_stock":true},{"title":"2.5kg | Coverage 12.5m²","offer_id":58122236461438,"sku":"RCD649","price":150.12,"currency_code":"GBP","in_stock":true},{"title":"5kg | Coverage 25m²","offer_id":58122236494206,"sku":"RCD650","price":207.32,"currency_code":"GBP","in_stock":true},{"title":"10kg | Coverage 50m²","offer_id":58122236526974,"sku":"RCD651","price":354.72,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1023\/9806\/7070\/files\/99fb1e7e8c939dd7897b199472917c1e.jpg?v=1790656422","url":"https:\/\/resincoatingsdirect.co.uk\/products\/epoxy-primer-2-part-system-for-enhanced-adhesion","provider":"Resin Coatings Direct","version":"1.0","type":"link"}